[Dec-2025] AVIXA CTS-I Dumps – Reduce Your Chance of Failure in CTS-I Exam [Q83-Q106]

Share

[Dec-2025] AVIXA CTS-I Dumps – Reduce Your Chance of Failure in CTS-I Exam

To help you achieve your ultimate goal, we suggest the actual AVIXA CTS-I dumps for your Certified Technology Specialist - Installation exam preparation to use as your guideline.

NEW QUESTION # 83
To avoid power and grounding issues, any audio cable longer than 15 feet (4.6 meters) should use _______.

  • A. A foil shield and drain wire
  • B. Common-mode rejection ratios
  • C. A balanced interface
  • D. Common-mode rejection

Answer: C


NEW QUESTION # 84
How often should your toolbox multimeter be sent to an accredited testing laboratory for recalibration?

  • A. Yearly.
  • B. Before the commencement of each project.
  • C. Never. It should be calibrated against your organization's highest-precision test instrument.
  • D. Every five years.

Answer: C


NEW QUESTION # 85
Typically, what type of connector finishes the shielded twisted pair cable?

  • A. XLR
  • B. TRS
  • C. RJ-45
  • D. USB

Answer: A


NEW QUESTION # 86
If existing components have to be reused in an AV system, what is a critical task that the installer must perform?

  • A. Test the equipment to make sure it is operational
  • B. Draw a schematic showing where the old equipment fits
  • C. Call the manufacturer to extend the warranty
  • D. Discard items that do not meet specifications

Answer: A


NEW QUESTION # 87
Hot spotting increases as _____ increases.

  • A. the projection cone
  • B. ambient light
  • C. surface area
  • D. gain

Answer: D


NEW QUESTION # 88
What piece of test equipment is used to measure speaker resistance in a 70v distributed audio system?
Response:

  • A. Ohm meter
  • B. Volt meter
  • C. Pink noise generator
  • D. Impedance bridge/meter

Answer: D


NEW QUESTION # 89
_______ can transmit AV signals and other data up to a distance of 1km (3,280ft) or more before signal quality is compromised.

  • A. Coaxial cabling
  • B. Shielded twisted-pair (STP) cabling
  • C. Unshielded twisted-pair (UTP) cabling
  • D. Multimode fiber-optic cabling

Answer: D


NEW QUESTION # 90
Which of the following choices lists the correct pinouts for the T-568A end of a crossover network cable (pin
1-8):

  • A. Gr, WGr, WOr, B, WB, Or, WBr, Br
  • B. WOr, Or, WGr, B, WB, Gr, WBr, B
  • C. Br, WBr, Or, WB, B, WOr, GR, WGr
  • D. WGr, Gr, WOr, B, WB, Or, WBr, Br

Answer: D


NEW QUESTION # 91
The two Ethernet standards for an 8-pin modular connector (sometimes called an RJ45) termination are:

  • A. E423A and E423B
  • B. RJ45A and RJ45B
  • C. RJ45B and RJ11A
  • D. T568A and T568B

Answer: D


NEW QUESTION # 92
What is a best practice when selecting fasteners for mounting AV equipment?

  • A. Use standards-rated bolts.
  • B. Use bolts that are available near the job site.
  • C. Use bolts with smooth heads.
  • D. Use bolts that are extra-long.

Answer: A


NEW QUESTION # 93
Crossover cables are used to connect:

  • A. a device's NIC to its MAC address
  • B. devices configured to accept different Data Link layer protocols
  • C. digital and analog devices
  • D. two devices without the use of an electronic crossover device

Answer: D


NEW QUESTION # 94
According to industry best practices, what is wrong with the picture above?

Response:

  • A. The cable loop is too small
  • B. Cable ties are too tight
  • C. The cables are unsupported
  • D. Poorly trimmed cable ties

Answer: C


NEW QUESTION # 95
Once an audio signal has left a microphone, what processor will it encounter first?

  • A. The preamplifier
  • B. The power amplifier
  • C. Acoustic echo cancellation
  • D. The audio mixer

Answer: A


NEW QUESTION # 96
Visual Acuity is __________.

  • A. 20/20 vision
  • B. the ability to perceive and assimilate visual information
  • C. the visual angle of 1 minute of arc
  • D. an optotype

Answer: B


NEW QUESTION # 97
The ANSI/AVIXA 2M-2010 Standard Guide for Audiovisual Systems Design Coordination Processes lays out a procedure for determining the:

  • A. project communication that needs to take place on a given project
  • B. functions and features that are required to support a given set of tasks
  • C. verification tests that should be performed during a given project
  • D. room types that are suitable for a given set of client needs

Answer: A


NEW QUESTION # 98
In which situations or environments is the system optimization method of gain adjustment preferable to the unity gain method? (Choose all that apply.)

  • A. Where clipping levels will not vary within the system
  • B. In performing arts centers and lecture halls
  • C. For installations with short deadlines
  • D. For systems with 750m V input signal levels

Answer: B


NEW QUESTION # 99
What does a microphone's polar pattern indicate?

  • A. Performance in cold temperatures
  • B. Sound sensitivity in different directions
  • C. 6dB drop-off at 270 degrees
  • D. Peak noise level

Answer: B


NEW QUESTION # 100
The second conductor of an unbalanced circuit _____.

  • A. is a shield around the wire used as the electrical circuit's return path
  • B. has the same impedance as the first signal conductor
  • C. carries an inverse image of the first signal conductor
  • D. is an insulated wire which transports the signal

Answer: A


NEW QUESTION # 101
DISCAS addresses the following viewing categories:

  • A. Full Motion Video
  • B. Analytical Decision Making
  • C. Passive Viewing
  • D. Basic Decision Making

Answer: B,D


NEW QUESTION # 102
Which is an RS232 parameter?
Response:

  • A. Subnet mask
  • B. Bandwidth
  • C. Polarity
  • D. Parity

Answer: D


NEW QUESTION # 103
Projector optics is defined as a _____.

  • A. light source and a series of lamps that carry an image on a screen
  • B. system of lamps and lenses that carry an image on a screen
  • C. series of mirrors and lights that carry an image on a screen
  • D. series of lenses that carry an image on a screen

Answer: B


NEW QUESTION # 104
What is a macro?
Response:

  • A. A single function activated by a switch
  • B. A function activated by a button
  • C. Multiple functions activated by separate buttons
  • D. A set or sequence of functions activated by a button

Answer: D


NEW QUESTION # 105
The back light _____.

  • A. is the brightest light on the subject
  • B. fills in dark spots which are created
  • C. shines on the subject's shoulders and hair
  • D. lights the background

Answer: C


NEW QUESTION # 106
......

Accurate & Verified Answers As Seen in the Real Exam here: https://endexam.2pass4sure.com/AVIXA-Communications/CTS-I-actual-exam-braindumps.html