Pass NACE-CIP1-001 Exam Latest Practice Questions Updated on Sep 16, 2022
NACE NACE-CIP1-001 Study Guide Archives
NEW QUESTION 48
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Rotating the dial too fast when taking measurements
- B. Measuring ditty, tacky, or soft films
- C. Taking measurements too far from the edge of a surface
- D. Failing to determine the base metal reading (BMR)
Answer: A,B,D
NEW QUESTION 49
A NACE Coating Inspector is permitted to transport coating material when:
- A. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- B. Asked to do so by the Owner's Representative
- C. The Inspector should never transport coating material
- D. Asked to do so by the Coating Application team
Answer: C
NEW QUESTION 50
Safety Data Sheets must be carefully reviewed by:
- A. The Application personnel
- B. The Inspection personnel
- C. The Owner's personnel
- D. All personnel involved in the job
Answer: D
NEW QUESTION 51
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. In the office only
- B. Only if the specification requires it
- C. In the field only
- D. At all times
Answer: D
NEW QUESTION 52
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. scratches the surface too deeply resulting in uneven coating application
- B. damages structural elements thereby speeding up the corrosion process.
- C. develops a polished surface, which is a poor anchor profile for most coatings
- D. develops a good anchor profile resulting in uneven coating application.
Answer: C
NEW QUESTION 53
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Shut the job down
- C. Permit coating to take place so as not to lose the blast
- D. Review the relevant standard with the Contractor
Answer: D
NEW QUESTION 54
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- B. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- C. Default to the owner's Inspection and Test Plan
- D. Bring the matter up at the pre-job conference
Answer: D
NEW QUESTION 55
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 56
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. alligatoring.
- B. checking.
- C. cracking.
- D. blistering.
Answer: B
NEW QUESTION 57
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks regardless
- B. Skip the checks and just record the same readings as you have been getting
- C. Keep doing the checks and consult the Owner's representative for direction
- D. Skip the checks as you are. confident the blast pressure is OK
Answer: C
NEW QUESTION 58
SSPC SP 1 identifies the use of:
- A. A wide variety of materials
- B. Organic solvents
- C. Inorganic solvents
- D. Biodegradable detergents
Answer: A
NEW QUESTION 59
The NACE Inspector should perform tests for soluble salts:
- A. When specified
- B. After surface preparation
- C. Prior to coating application
- D. Prior to surface preparation
Answer: A
NEW QUESTION 60
Dew point is the temperature at which
- A. the air is saturated.
- B. condensation occurs.
- C. water freezes.
- D. humidity decreases
Answer: B
NEW QUESTION 61
Osmotic blistering is most likely to occur as a result of
- A. airless spray application
- B. inadequate anchor pattern/surface profile.
- C. applying tine coating too thin.
- D. overcoating a surface contaminated with chemical salts.
Answer: A
NEW QUESTION 62
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 105 Gauge Readings resulting in 35 Spot Measurements
- B. 75 Gauge Readings resulting in 25 Spot Measurements
- C. 45 Gauge readings resulting in 15 Spot Measurements
- D. 225 Gauge Readings resulting in 75 Spot Measurements
Answer: D
NEW QUESTION 63
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. commercial blast cleaning.
- B. brush-off blast cleaning.
- C. white metal blast cleaning.
- D. near-white metal blast cleaning.
Answer: B
NEW QUESTION 64
Galvanic corrosion occurs on which of the following substrates:
- A. Fiberglass Reinforced Plastic
- B. Wood
- C. Concrete
- D. Metal
Answer: D
NEW QUESTION 65
A magnetic pull-off type gauge is a good choice when:
- A. When an intrinsically safe tool is required
- B. Accuracy is not required
- C. When working on non-ferrous metals
- D. Performing an adhesion test
Answer: A
NEW QUESTION 66
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Power tools
- B. Abrasive blast nozzles
- C. Airless spray equipment
- D. Hand tools
Answer: A
NEW QUESTION 67
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. A general guide
- B. Pass/fail criteria
- C. A method to grade surface profile
- D. A final conflict resolution method
Answer: A
NEW QUESTION 68
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 6.35 cm (2.5 inch)
- B. 2.5 millimeters (.10 inch)
- C. 1 cm (.39 inch)
- D. 2.5 cm (1 inch)
Answer: D
NEW QUESTION 69
Passivation can best be described as:
- A. Treating metal with a liquid inhibiter
- B. Complete elimination pf the corrosion process
- C. A coating layer applied to the surface to inhibit corrosion
- D. A protective metallic oxide surface layer that slows corrosion
Answer: D
NEW QUESTION 70
Conventional spray is a good choice when:
- A. High viscosity coatings are being applied
- B. High transfer efficiency is required
- C. High production rates are required
- D. High quality finishes are required
Answer: D
NEW QUESTION 71
......
NACE-CIP1-001 Questions Prepare with Learning Information: https://endexam.2pass4sure.com/CIP-Level-1/NACE-CIP1-001-actual-exam-braindumps.html